12v kit for the Segway Ninebot G30 models

Important!! SEE VIDEO BELOW BEFORE PURCHASE.

Important! Watch the video below about the software before purchasing a battery pack. If you have locked software, you need to send in the motherboard for an ST link. It costs 299 SEK plus shipping if you send in the card and 549 SEK if you come in with the scooter. Updates in the Segway app have been released that prevent the scooter from having modified software. This can be bypassed with an ST link or by buying a new motherboard. If you have already hacked your scooter, there are no problems having this kit as you can use our software. If you're unsure, you need to contact us and we'll help you test to see if it works, alternatively, you can come by our workshop for us to check.

There's also a motor with a serial number that says PADH on the middle line of the serial number on the motor. In such a case, this kit won't work as we haven't tested this motor and the software does not work with this motor. There is a picture of it at the bottom of the page.

This kit is only suitable for Segway Ninebot G30.

Delivered within a week from ordering.

Beware of others trying to sell these kits in Sweden, as we have examined their kits and found many defects that they don't consider when building their kits. We have no partnerships regarding our battery kits, so our kits can only be bought from us!

What is a 12v kit?

A 12v kit is a series-connected battery that increases the voltage supplied to the motherboard, making the scooter faster and stronger.

The speed depends on the motor you have. With a gen 1 motor, this kit provides 36-40km/h, while with a gen 2 motor, it provides 41-45km/h.

The speed depends on the model of G30 you have and where it was manufactured. Therefore, the top speed varies within an interval of 5km/h.

It also becomes faster uphill and at the start. Some choose to drive in D mode sometimes as this power is not always needed.

The top speed varies depending on your weight and how charged the battery is.

Regarding tire pressure, it's important to have over 55psi if you weigh up to 80kg, 65psi for up to 90kg, and around 70psi for around 100kg.

If you have solid tires, we advise against having a 12v kit as these make the scooter too hot because they are heavy to drive and the motherboard can't handle it.

There are two different setups.

For the black model: Since this model has two charging ports and you only use one, you get instructions on how to connect the battery charging to this port. No soldering iron is needed as everything required for this connection is included.

For the white model: You get the charging port on the bag.

What's included?

• Instructional video on how to install and necessary info.
• 12v 19.4Ah battery
• All necessary cables
• 2L bag
• Charging port on the bag
• 12v 3A charger
• Software
• Installation manual

Installation of our kits costs 449 SEK.

If the restrictions below are not followed, you will burn the electronics in it. We are not responsible for any damage to the scooter. We have tested these kits and set restrictions to make them sustainable. The scooter is also damaged without a 12v kit if these restrictions are not followed.

Here's what's important to stick to:

• Have over 55psi if you weigh 70-80kg, over 65psi if you weigh 80-90kg, over 70psi if you weigh over 90kg.
• Do not ride up too steep hills. How do you know? If you're full throttle and fall below 16km/h uphill, you should get off as the motor can't get rid of the energy coming from the motherboard and battery.
• Do not brake hard for the first 10% when the battery is fully charged as it cannot recharge the energy from the braking, instead it becomes heat.
• Make sure to have the front brake tightened so that it relieves the electronics when you brake.

Video about the software and the new motor:

All these things also apply if you don't have a 12v kit and you can damage the scooter because of this.